Constructive connector characteristics - Tambour door
Access
Ribbon : Main data > Main data > Element Manager > Connections > Connector
General Information
The constructive connector characteristics describe certain features of the connector. For example, you can modify the position of the connector in the article.
Attributes
| Preview | Characteristic-Name | Values | Explanation |
|
Sliding and folding door type/ Part type (SFTYP) |
1 = Outside runner/ Glider 3 = Slide 10 = Rips 11 = Handle strips 12 = 90°-Edge 13 = Shutter housing guide 14 = Winding mechanism 15 = Winding mechanism rods 16 = Pilaster strip/ Lesene 17 = Top cover 18 = End caps 19 = Center stoppers 20 = Brakes 21 = Rope systems 22 = Winding rod extensions 23 = Caddy brake |
The characteristic defines the selected connector type. |
|
Shortening the slide (SFR_SUB_SLIDE) |
Number (editable) |
The characteristic indicates the decrease of the slide. Negative values lengthen the slide. |
|
Offset of the front slide (SFR_OFFSET_SLIDE_FRONT) |
Number (editable) |
The entered value shifts the front slide to the back. |
|
Offset lateral slide to the side (SFR_OFFSET_SLIDE_INSIDE) |
Number (editable) |
The characteristic indicates how far the lateral slide will be shifted to the side. |
|
Offset back slide (SFR_OFFSET_SLIDE_BACK) |
Number (editable) |
The entered value shifts the back slide to the front. |
|
Additional quantity of invisible slats (SFR_INVISIBLE_COUNT) |
Number (editable) |
The additional numbers of blades in the invisible section are defined with the characteristic. If special blades were created for this section, then these will be used. Otherwise the normal blades are used. |
|
Invisible rips (SFR_IS_INVISIBLE) |
1 = Yes 0 = No |
Yes = A second type of blades is defined for using in the invisible section. (e.g. favorable blade) No = There are no special blades for the invisible section. |
|
Groove construction (GROOVE_CONSTRUCTION) |
Text (editable) |
Groove construction principle |
|
Extension of the tambour roll tops (SFR_ADD_LENGTH) |
Number (editable) |
The characteristic defines the extension of the tambour roll tops. The characteristic is only evaluated if it is „ Additional quantity invisible rips “ = 0. The extension of the tambour roll tops has an effect on the number of the tambour slats:The length of the tambour roll tops is added to the value of the extension; and then divided by the width of a slat. The rounded up result is the number of the slats. |
|
Minimal length tambour roll tops (SFR_MIN_LENGTH_CADDY) |
Number (editable) |
The characteristic shows a minimum length for the tambour roll top. The characteristic also has an effect on the calculation of the numbers of the tambour slats. A minimum measurement for the tambour roll top is required because an installed Caddy-Stopper in the article is only then effective with a certain length of the tambour roll top. The characteristic is evaluated as soon as one of the connectors within the set has the characteristic „ Sliding-and folding door type/Part type = Caddy-Brake “. |
|
90° edges only backwards (SFR_ONLY_BACKWARD) |
Yes No |
Yes = The 90°-Edges are only used at the back No = The 90°-Corners can be used in the front and back. If this characteristic is not entered, the characteristic-value will automatically be read-out as "No". |
|
Thickness (SFR_THICKNESS) |
Number (editable) |
The characteristic defines the thickness of the connector. The characteristic can be entered in blades, gliders and winding mechanical rods. |
|
Glider type (SFR_FOR) |
0 = Glider for handle strip 1 = Glider for slats 2 = Glider for mid handle strip |
This characteristic defines the type of glider. |
|
Heightening / Reduction of ribs (SFR_HEIGHTENING) |
Number (editable) |
The height of the ribs is increased by the entered value of the characteristic. A negative value minimize the height of the rib. |
|
Shortening inside bar handles on both sides (SFR_SUB_HANDLE_RAIL) |
Number (editable) |
The inside bar handles are shortened on both sides to the entered value. |
|
Reduction of both sides (SFR_SPACE) |
Number (editable) |
The characteristic defines the space from the tambour slat to the slide. The entered value is subtracted from both sides of the tambour slat. |
|
Width (SFR_WIDTH) |
Number (editable) |
The characteristic defines the width of the connector. The characteristic can be entered in blades, winding rods, inside bar handles and middle inside bar handles. |
|
Overlapping top cover (SFR_OVERLAPPING_COVER) |
Number (editable) |
The top is lengthened on both sides to the entered value. |
|
Overlapping top cover 2 (SFR_OVERLAPPING_COVER_2) |
Number (editable) |
The top is lengthened on both sides to the entered value. The characteristic is only used on the side of the bar handle. If this value is not entered, the characteristic-value from „ Overlapping top cover “ will be taken. |
|
Real handle strip or mid handle strip (SFR_IS_CENTER_HANDLE_RAIL) |
0 = Real inside bar handles 1 = Middle inside bar handles |
0 = A normal inside bar handle is inserted 1 = A middle inside bar handle is inserted. If the characteristic is not stored, a normal inside bar handle will be inserted. |
|
Y-Offset of the deviating point (SFR_BAR_DISTANCE_1) |
Number (editable) |
The return point is shifted to the back, into the carcass by the entered value. |
|
Distance axis 1 to axis 2 (SFR_BAR_DISTANCE_2) |
Number (editable) |
The characteristic defines the distance between axis 1 to axis 2 of the windings. |
|
Z-Offset of the deviating point (SFR_BAR_OFFSET) |
Number (editable) |
The return point is shifted to the bottom with the entered value. |
|
Name of the cross-section geometry principle (SECTION) |
Cross-section geometry principle |
In this feature the name of the cross-sectional geometry of the imos database is stored. The cross-sectional geometries can be created with the help of the Contours Wizards and edited with the Element Manager. |
|
Reduction of the winding mechanical rods on both sides (SFR_SUB_BAR) |
Number (editable) |
The winding mechanical rods are shortened on both sides to the entered value. |
|
Minimal length of the shaft (SFR_MIN_WIDTH) |
Number (editable) |
The characteristic shows the minimum length of the winding mechanical rod. Winding mechanical rods can be pressed together to a certain value and therefore shortened. The characteristic-value indicates the minimum length for the rod. |
|
Color Principle (COLOR) |
Color Principle | The characteristic can be entered in blades, slides, tops, pilasters and inside bar handles. |
|
Reduction of the pilaster strip on both sides (SFR_SUB_STRIP) |
Number (editable) |
The characteristic defines the shortening of the pilaster. The entered value is subtracted from both sides of the pilaster. |
|
Position of the middle handle strip (SFR_CENTER_ HANDLE_DISTANCE) |
Linear Division Descriptor | The middle inside bar handle is inserted in the center by default. The characteristic defines the position of the middle handle strip. |
|
Size of the center gap of the front slide (SFR_SPLIT_SLIDE) |
Number (editable) |
Only relevant with double sided stop. Indicates how often the front slides should be split in the center. If not available, then the front slides are not split. |
|
Use slide just as front slide (SFR_ONLY_FRONT) |
Yes No |
The characteristic defines the use of the slide. Yes = The slides are only used as front slides. No = The slides can be used as front-, side- and back slides. |
|
Example cabinet height 1 (SFR_EXAMPLE_HEIGHT1) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 1 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 1 “. |
|
Example cabinet height 2 (SFR_EXAMPLE_HEIGHT2) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 2 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 2 “. |
|
Example cabinet height 3 (SFR_EXAMPLE_HEIGHT3) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 3 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 3 “. |
|
Example winding diameter 1 (SFR_EXAMPLE_DIAMETER1) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 1 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 1 “. |
|
Example winding diameter 2 (SFR_EXAMPLE_DIAMETER2) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 2 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 2 “. |
|
Example winding diameter 3 (SFR_EXAMPLE_DIAMETER3) |
Number (editable) |
It depends on several parameters how the winding is inserted. These include the cabinet height. With this characteristic „ Example cabinet height 3 “ a construction is defined which creates a functional relationship with the characteristic „ Example winding cross-section 3 “. |
|
Quantity of rips between glider (SFR_GLIDER) |
Number (editable) |
The entered characteristic-value indicates how often a glider can be installed. For example, if a 3 is entered, a glider will be inserted on every third blade. If this characteristic does not exist, a 1 will be used as a standard value; then a glider is inserted for every blade. |
|
Oversize front slide (SFR_OVERSIZE_SLIDE) |
Number (editable) |
The characteristic is entered on end caps and only evaluated on given slides. The slides will be extended to the entered value on both sides. |
|
Oversize front slide 2 (SFR_OVERSIZE_SLIDE_2) |
Number (editable) |
The characteristic is entered on end caps and only evaluated on given slides. The slides will be extended to the entered value on both sides. The characteristic is only used on the side of the bar handle. If this value is not entered, the characteristic-value from „ Oversize front slide “ will be taken. |
|
Back slide same length as front slide (SFR_BACK_SLIDE_EQUAL) |
1 = Yes 0 = No |
Normally the back slide is created as long as necessary. As a general rule: length of the front slide minus article depth results length of the back slide. The value 1 results that the back slide is as long as the front slide. |