Generate cutting pattern part

Access

iXplorer > Methods

General Information

In a cutting pattern part, you can arrange multiple parts that have the same material. The formats of the cutting pattern part panels are referenced from the Material principle.

Note: Make sure that the Show Cutting Pattern Part checkbox is selected in the Visu Manager . Otherwise, you will not be able to see the cutting pattern part in the drawing area.

The following possibilities are available for generating and editing cutting pattern parts:

The possibilities are described below.

Cutting pattern parts can be transferred to the following cutting optimizations during process data transfer (Cutlist) : (as of August 2023)

  • ardis
  • CutRite

To obtain or configure the appropriate CFG, contact Sales or the imos Hotline.

Behavior

  • When you delete a part, it is also deleted in the cutting pattern part. When you delete the last part that was included in a cutting pattern part, the cutting pattern part is deleted as well.
  • When editing/ refreshing an article, all its parts are deleted and recreated in the process; the parts are deleted along with the corresponding parts in cutting pattern part.

Method Generate Cutting Pattern Part

The function is optimized for front elements such as doors, fillers and drawer fronts to be able to influence the veneer pattern across multiple fronts. But it can generally be applied to all types of parts.

  1. Select parts to be arranged in a cutting pattern part.

    Info: It is recommended to select first, because the CAD orbit cannot be used for navigation while the function is active.

    Tip: Use the iX Elements filter to select parts with specific properties.

  2. Click on the Generate Cutting Pattern Part method in the iX Methods palette.
  3. Make a right click in the drawing area to confirm the selection.
  4. Define at which coordinates the cutting pattern part is to be drawn/ positioned. After confirming the position, a configuration mask is loaded in the iX Properties palette.
  5. Configure the Cutting Pattern Part and click Apply (check mark). The cutting pattern part will be generated in the drawing area.

Note: If you have a very nested front image, you may still need to manually adjust the layout in the cutting pattern part.

Method Generate Cutting Pattern Part

Optimized for work surfaces, base skirtings, top valances and light valances.

See Generate Cutting Pattern Part .

Generate a Cutting Pattern Part automatically

On request, an imos service employee can activate the function "Automatically generate cutting pattern part from veneer mother part" in order to automatically group child parts according to veneer pattern/ grain pattern. In addition, different arrangement types can be defined on request.

Note: The option "Keep front position" cannot be defined during automatic generation and is therefore not taken into account.

For grouping, you can use the field Veneer ID in the production info. You can assign this Manufacturing Info to corresponding Part Definitions. With the veneer ID, cutting pattern parts will be generated automatically for each inserted article.

Example: Veneer ID "horizontal" for a Part Definition with a grain angle of 90°.

Tip: Use Part Definition variables so that you can quickly make changes in the Variables dialog instead of in each field individually.

Alternatively, you can assign the Manufacturing Info with the veneer ID in the Construction principle in the Article Designer. Especially for drawers, in the "advanced" drawer settings you will find "Front Manufacturing Info" in addition to the "Manufacturing Info" field.

Method Edit Cutting Pattern Part

You can subsequently edit an existing cutting pattern part, e.g. to manually change the position of parts on the panel.

  1. Select the generated cutting pattern part (at part level).
  2. Click on the Generate Cutting Pattern Part method in the iXplorer palette. A configuration mask is loaded in the iX Properties palette.

    Note: If the method does not appear in the palette, click Refresh in the Elements tree and make sure that the correct level is selected in the Elements tree.

  3. Make desired changes in the configuration mask.
    • Change X/ Y dimensions
    • Keep front position and corresponding options
    • Change the cutting distance (overrules "Keep front position")
    • Adjust (the panel size -> overrides manually entered dimensions in X/Y)
  4. Click "Apply" (check mark).

Options - General

Inherit Workings to Cutting Pattern Part Yes:

Machining the child part such as the drillings, pockets etc. are inherited to the mother part which means the cutting pattern part. In this process no outer contours are transferred. Then the information can be used for the CNC.

No:

With this setting the cutting pattern part is transferred to the Cutlist Tool without workings. Thereby no information is generated for the CNC.

Automatic flip

Yes:

If the part has only machining from the bottom, the part is automatically flipped in imos , so that the machining can take place from the top.

No:

Here the workings are not checked and the part is just clamped on the machine. It is also possible to generate a second working then.

Generate NC-Program

The setting overwrites the Manufacturing Information for the child parts.

Yes:

Additional NC-Programs are generated for the manufacturing information of the child parts

No:

NC-Programs are only generated for the cutting pattern part (mother part).

Part in cut list

The setting overwrites the Manufacturing Information for the child parts.

Yes:

The child parts are output in the cutlist.

No:

Only the cutting pattern part (mother part) is output in the cutlist.

Part in part list

The setting overwrites the Manufacturing Information for the child parts.

Yes:

The child parts are output in the bill of material.

No:

Only the cutting pattern part (mother part) is output in the bill of material.

Cutting material

Prerequisite:

  • "Merge" must not be checked.
  • The selected parts use the same material.

The Cutting Material option helps you avoid creating cutting pattern parts that are too large. Select the panel format whose dimensions should not be exceeded. In the list you will find the formats that are defined in the corresponding Material principle.

As a result, you will receive one or more cutting pattern parts accordingly.

Note: The option serves as a supporting tool . The cutting pattern parts do not adopt the dimension of the selected panel.

Options - Front definition

If Keep front position is active, front parts are arranged on the cutting pattern part according to the front definition ("front unfolding"). In other words, their position relative to each other is not changed. Turn on the option for front definitions, where you want the grain to give a seamless image.

Tip: Use the iXplorer filter to isolate the parts that should be in a seamless front image.

Note: In the case of very nested front images, you may have to check and rework the cutting pattern part.

You can make the following settings on a cutting pattern part with front definition:

Merge

Merge parts, that would be placed in separate cutting pattern parts due to their position, into one cutting pattern part, for example the fronts of a corner cabinet.

Where necessary, make manual corrections, e.g. to skirting boards.

Mirror Align the cutting pattern part in CAD by mirroring it.
Transition distance

Available when Merge is ticked. Changes the distance between the merged parts.

Note: This setting is irrelevant when transferring to Cut Optimization services and when generating NC data.