Article Designer – Trims

Access

iX Elements Palette > [Article Designer selected] > Tab Parametrics > [Side / Door/ Back selected in Elements Palette ] > iXplorer Properties Palette > Tab Trims

[ Two adjacent parts selected ] > iXplorer Properties Palette > Tab Methods >Method "Change joint"

General Information

There are different possibilities to change the trim/ joint between two parts . When you edit an Article Designer, you can go to the tab Trims of the affected sides. You can either assign a fix value using the dropdown box or you can assign numerical variables for part trims . Alternatively, there is the method "Change joint" in the iXplorer Methods Palette when two parts are selected.

The number of parts, for which an oversize can be set, changes depending on which type of part is activated and in which construction mode you are working on.

For a seamless closure for visible article edges that are interrupted by cutout articles, you can now define the edge trims to the side and back panel, and set them to Short

Options

Previous

The previous is evaluated counter-clockwise.

Long

The selected part continues through and butt joins with the previous part. With a diagonal previous part, the selected part automatically adjusts to the angle.

Short

The previous part continues through and butt joins with the selected part.

Mitre

The selected part joins with the previous part in a mitre.

Rectangular When using this function, the selected part is not adjusted, and the joining edge is generated with a 90° edge.

The trim can be also defined with a variable. Also read the section Define trims as variables

Next

The next is evaluated counter-clockwise.

Long

The selected part continues through and butt joins with the next part. With a diagonal next part, the selected part automatically adjusts to the angle.

Short

The next part continues through and butt joins with the selected part.

Mitre

The selected part joins with the next part in a mitre.

Rectangular When using this function, the selected part is not adjusted, and the joining edge is generated with a 90° edge.

Frame parts The trims for the frame parts can just be defined in the front view and only if a frame has been created in the article.
Top/ Bottom Shelf

The trims for the top shelf/bottom shelf can only be set for the construction in the topview.

By entering a positive value, a protrusion of the selected part for the top shelf/bottom shelf is created. A negative value creates an offset.

Door/ Back panel

The trims for the door/back panel can only be set for the construction in the front view.

By entering a positive value, a protrusion of the selected part for the door/back panel is created. A negative value creates an offset.

Left and Right Sides

The trims for side panel can only be set for the construction in the side view.

By entering a positive value, a protrusion of the selected part is created. A negative value creates an offset.

Oversizes

With the support of an oversize an entry of a positive value can effect a protrusion and an entry of a negative value shortens the selected part.

If one of the oversize fields is not editable, then the settings are derived from the construction principles. Click on the button next to the entry to activate this field. Thereby the settings from the principles are not evaluated anymore but the entry field now.

All settings are immediately visible in both previews and in the schematic article preview.

The oversize can also be defined with a variable . You can find the option for Variables by right-clicking in the field.

Angle

By entering a value in the field tilt angle, the selected part is tilted referring to the base area. A negative value effects a tilting into the carcase and a positive value out of the carcase.

It can also be defined with a variable . Call therefore the function iX - variables by a right mouse click.

Divider inset

By entering a value in the field tilt angle, the selected part is tilted referring to the base area. A negative value effects a tilting into the carcase and a positive value out of the carcase. The dividers of the zones below are also revealed along with it.

It can also be defined with a variable . Call therefore the function iX - variables by a right mouse click.

Zone reveal

By entering a positive value in the field zone reveal, the complete zone with all parts is revealed in the direction to the center of the article. A negative value effects a tilting into the carcase and a positive value out of the carcase. The dividers of the zones below are also revealed to this value.

It can also be defined with a variable . Call therefore the function iX - variables by a right mouse click.

Define trims as variables

You can control the trims in the Article Designer with a numerical variable. For this, click the button "Variable" in the respective field. Now you can assign Variables of the type Number in the input field.

The kind of trims are defined by the numerical values 0,1,2,3,4.

Possible values:

  • Inset = 0 and 1
  • Onset = 2
  • Mitre = 3
  • Perpendicular = 4

If you later decide, not to use a numerical variable in the field, click the button "Variable" again.

Related topics