Part Editor - Parts
Access
Element Manager > Construction Principle > Parts > Part Definition > Basic settings > Part category
General Information
The "Parts" tab summarizes functions for adding and editing child parts and stretchable purchased parts. Depending on which one you edit, the Interactive Graphic and the availability of properties change.
For constructing, use the reference points that you previously created on the tab "Reference points".
Create child parts
Prerequisite:
On the tab General , Multi-part element is checked.
You created reference points in the tab Reference points , which you can use to define the contour of the part.
Procedure:
- In the toolbar , click on New Part .
-
In the Interactive graphic , select the Reference points that are to form the corner points of the child part.
If more than two points are selected, a panel part will be created. If only two points are selected, the panel part will be generated vertically and the height will be determined using the Z dimension entered.
The order in which you select the points determines the numbering of the part edges.
Tip: The numbering can be changed later with the tool Rotate Edges .
-
In the Properties sidebar , assign a Part Definition .
Optionally, fill out further properties. See Options - New Part .
- Click Apply to create the part.
Result: The part is listed in the tree for parts . It can be subsequently edited using the tools in the toolbar.
Create Stretchable Purchased Parts
Prerequisite: You created reference points in the tab Reference points , which you can use to define the contour of the part.
Procedure:
- In the toolbar , click on New SPP .
-
In the Interactive Graphic , select two reference points that will form the start and end point of the SPP.
The SPP will be extruded along the axis resulting from the start and end point.
The order in which you select the points determines the numbering of the component edges.
Tip: The numbering and thus the orientation can be changed later with the tool Rotate Edges .
-
In the Properties sidebar , assign a principle for Stretchable Purchased Parts .
Optionally, fill out further properties. See Options - New SPP .
- Click Apply to create the SPP.
Result: The SPP is listed in the tree for parts . It can be subsequently edited using the tools in the toolbar.
Tools
| New Part |
Create a new child part (panel). See Create child parts . The interactive graphic and the availability of properties in the sidebar change according to the element type child part . |
| New SPP |
Create a new stretchable purchased parts. See Create stretchable purchased parts . The interactive graphic and the availability of properties in the sidebar change according to the element type stretchable purchased part (SPP) . |
| Delete | Delete points that you have selected in the tree Parts . |
| Rotate edges |
The edges of the highlighted secondary part are rotated clockwise. The orientation of the part is not changed. |
| Change part orientation |
Only available for parts. The part orientation is rotated by one position. The current situation is displayed in preview. |
| Turn part |
Only available for parts. The part is rotated around axis X. Rotated parts are highlighted in blue in the preview. |
| Detach points | All selected reference points are released so that a new point selection can be made. |
Options - New Part
HINT: As a rule, you cannot make subsequent changes to a component in the Component Editor. In this case, delete the affected part from the parts list and create it again with the desired settings.
| Apply (check-mark) |
Available when the options have been opened by clicking on the tool New Part . With a click on the button, the child part is generated according to the selected reference points and the assigned Part Definition. |
| Discard/ Cancel |
Available when the options have been opened by clicking on the tool New Part . Cancels the New Part process and discards current entries in the options. |
| Construction Points |
The list contains all selected construction points. With the support of the list you can check the defined construction points before generating the daughter part from these points. You empty the list when you call the function Detach points . |
| Part Definition | Via a click on the button you will switch to the Element Manager where you can select a part definition. The selected part definition will be applied to the generated part. |
| Z Offset |
The offset contains the displacement of the highlighted part in the direction of the part thickness. The reference points are the bottom edges of the multiple part element as well as the daughter part |
| Z Value | This value is only relevant when only two construction points are chosen. The entered value determines the height of the highlighted part. |
| Thickness of part | Defines the thickness of the part by default. But if the checkboxes Do not create a part, only apply machining and Clean out are checked, a pocket or an entire cut-out in the specified thickness is created instead. |
| Connectors |
A click on the button opens a context menu. There you can see the following options. Inherit to Multi Part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are assigned to the primary part. Apply to this part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are only assigned to the secondary part. Inherit to this part and Multi Part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are assigned to both the primary and the secondary part. |
| Surface | Controls whether the surface should be inherited from the multi-part or not changed at all. |
| Do not create part, only create cutout contour |
When ticked, an inner contour is created in another part when it is overlaid by the inner contour; the inner contour is based on the shape of the assigned part definition. Here, the material thickness from the part definition is used as the inner contour depth and the profile of edge 1 from the part definition is used as the profile for the inner contour drawing. (Alternatively, a different thickness can be specified in the Thickness of part field.) The special thing about it is that inner contours defined by reference points behave parametrically and adapt to dimensional changes. This is particularly suitable for frame panel doors and doors with elaborate milling contours (style doors). To ensure that the distances are variable and do not "warp" when the article contour is adapted, e.g. to a sloping roof, it is necessary to define the linear division on the basis of a reference length. This can be e.g. be the length of the left or right side of the cabinet. Especially for this purpose, there are constants that return the desired edge length (see Variables and Constants in the Part Editor). See also One editor for all part types . |
| Profile alignment |
Is evaluated if the checkbox Do not create part, only apply machining is checked. Controls how the profile from the part definition is unwound or aligned: inside, outside or center. |
| Offset of the part contour |
Is evaluated if the checkbox Do not create part, only apply machining is checked. Controls the inward or outward offset of the contour. |
| Clean out |
Is evaluated if the checkbox Do not create part, only apply machining is checked. Cleans out everything within the contour to create a pocket or an entire cut-out. The depth of the pocket depends on the assigned part definition or the Thickness of part field. |
| Contour width |
Is evaluated if the checkbox Do not create part, only apply machining is checked and the checkbox Clean out is not checked. Controls the width of the inner contour that is created according to the part's shape. |
Options - New SPP
| Apply (check-mark) |
Available when the options have been opened by clicking on the tool New SPP . With a click on the button, the start and end point as well as the assigned principle are evaluated and the SPP is generated accordingly. |
| Discard/ Cancel |
Available when the options have been opened by clicking on the tool New SPP . Cancels the New SPP process and discards current entries in the options. |
| Purchased Part Definition | Via a click on the button you will switch to the Element Manager where you can select a principle. The selected principle is used for the generation of the SPP. |
| Offset relative to bottom face of part |
The position/ offset of the SPP in Z-direction depends on the insertion point of the section geometry related to the bottom of the part. The value defines the offset of the insertion point of the section geometry related to the bottom edge. You can edit the insertion point of the section geometry at any time. Therefore open the entry Reference point in the Stretchable Purchased Part. |
| Plus part thickness | If this function is activated the part thickness will be included in the offset. Thereby the offset is related to the bottom of the part but to the top. |
| Rotation around start and endpoint | In order to rotate the purchased part around the extrusion axis, enter a corresponding angle of rotation in the field. A positive angle results a rotation counterclockwise, a negative angle a rotation clockwise. |
| Start mitre angle | You can define the angle of the SPP at the start and end point. Thereby it is possible to mitre the SPP. |
| End mitre angle | You can define the angle of the SPP at the start and end point. Thereby it is possible to mitre the SPP. |
| Connectors |
A click on the button opens a context menu. There you can see the following options. Inherit to Multi Part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are assigned to the primary part. Apply to this part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are only assigned to the secondary part. Inherit to this part and Multi Part The modifications of the connector which are assigned to the secondary part in the part definition via the connector situation are assigned to both the primary and the secondary part. |