Design parameter
Access
imos Ribbon : Main data > Main data > Element Manager > General Rules
Organizer > Tab Element Manager > General Rules
General Information
A view data principle sums up different values of gap dimensions.
The Design Parameter principles are applied to front parts where front defintion/ Use design parameters is activated in the construction principle. The settings are for the complete order as far as no view data principle has been allocated to individual articles. The difference between the view data principles is the onset and inset front parts. The onset front parts can define if the gap dimension is set or the overlays of the front on the carcase.
Furthermore, view data can be applied as variables. If a variable of the type view data principle has been applied, a directory with the name imos -Variables will appear in the left selection. The variable name and the current value of the variables are shown. You can select the required variable and allocate it to an order or article.
Options
Default settings
| Top | The entered value defines the gap of the front to the top exterior carcase. |
| Below | The entered value defines the gap of the front to the bottom exterior carcase. |
| Links | The entered value defines the gap of the front to the left exterior carcase. |
| Right | The entered value defines the gap of the front to the right exterior carcase. |
| Angled | The entered value defines the gap of the front to the angled exterior carcase. |
| Horizontal Centered | The entered value defines the horizontal gap between two fronts, i.e. two drawer fronts. |
| Vertical Centered | The entered value defines the vertical gap between two fronts, i.e. two drawer fronts. |
| Angled Centered | The entered value defines the angled gap between two fronts. |
| Overlay instead of gap | If the function is activated, the overlay is calculated and not the gap anymore. The overlay is the overlapping of the front to the carcase. |
|
Enable outside gaps for Divider . |
This function is for fronts that are on a divider and do not refer to any other front. If the function is not activated, the gap is calculated like for a divider that means from the middle of the divider. Whereas, if the function is activated, the gap is calculated in the same way as for an outer panel. The function can also be applied with C-constructions. If a carcase side has been defined as a divider in the Article Designer, then the front can be calculated as you may require. |
|
Use as default for Inset |
If the function is activated, the values entered at the top are also applied for the inset constructions. If the checkmark is not marked next to the function, additional fields will appear for evaluating specially inset constructions. In addition the fields top, bottom, left, right and slope will appear. |
|
Use as default for overlay |
If the function is activated, the values entered at the top are also applied for the onset constructions. If the checkmark is not set next to the function, additional fields will appear for evaluating specially onset constructions. In addition the fields top, bottom, left, right and slope will appear. |
Construction
| Insert base |
If the function is activated, a base construction is constructed under all cabinets. In addition the following parameters are shown. |
| Base notch | With this function you can automatically process base notches in the panel sides. It is possible to insert notches in the front and back of the panel side. The dimensions for the notches are defined in the fields ‘depth and height’. In the Article Designer you can define which filler construction with which defaults should be inserted. |
| Height base constructions |
The function is shown when the flag Inset Base is active. The entered value defines the height of the base notch. |
| Depth base constructions front |
The function is shown when the flag Inset Base is active. The entered value defines the depth of the base notch at the front. |
| Depth base constructions back |
The function is shown when the flag Inset Base is active. The entered value defines the depth of the base notch at the back. |
Search Parameter
| Search Radius | The front and carcases are searched for within the defined radius to apply the view data principles. Parts outside the radius are not considered. |
| Maximum Length Distance | If several doors are inserted one below the other in an article, then it is possible that the gaps are minimal offset and therefore no continuous vertical gap is revealed. With this function the doors are shown as an element so that a continuous gap is revealed. The entered value indicates to which distance the doors should be set up as an element. |
| Center Gap on Dividers | If this function is activated, the gap for double doors is always calculated from the center of the divider. By doing this, the double door might have two fronts with different widths. |
| Prefer frame parts |
Takes front frame parts in the Article Designer into account. With activated function inset fronts and frame parts will interpenetrate. |
|
Outside gaps on face frame parts |
Up to now the gaps for frame parts have always been evaluated as an overlay. With the function ‘Outside gaps on face frame parts’ the gaps are evaluated as outside gaps. |
| Groove construction | With the button you can select a principle from the groove construction. So that e.g. the panel side can generate a groove in the door. |
| Gap direction | The function defines in which direction the groove should be calculated. This only leads to different results if the sides and doors are not perpendicular to one another. |