Section Geometry
Access
imos Ribbon : Main data > Main data > Element Manager > Contours
Organizer > Tab Element Manager > Contours
General Information
You can use a Section Geometry to apply it to a Stretchable Purchased Part. The contour is drawn as a not closed polyline.
Options
Sample Dimensions
The sample dimensions act as an illustration for the contour. If you use relative values for generating the contour it will be no problem to use the contour for elements with other dimensions.
| Dimension X | Sample dimension of the contour in X-direction. |
| Dimension Y | Sample dimension of the contour in Y-direction. |
Elements:
Starting point
The start point is defined by the coordinate in X- and Y-direction. You can define for both direction whether the coordinates shall be interpreted absolute or relative.
Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions.
Line
| Type |
You can define the position of the line endpoint in different ways. Also see Difference between relative and absolute segment coordinates . There are the following options: Endpoint The line is defined by the position of the endpoint in X- and Y-direction. The line is defined by the position of the endpoint in X- and Y-direction. You can define if the coordinates shall be interpreted absolutely or relatively. Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. Length and Angle The line is defined by the length and the angle related to the last point. The values can be defined absolutely or relatively. Angle and X-coordinate The line is defined by a start angle and the position of the endpoint in X-direction. The angle and the X-coordinate can be defined absolutely or relatively. Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. Angle and Y-coordinate The line is defined by a start angle and the position of the endpoint in Y-direction. The angle and the Y-coordinate can be defined absolutely or relatively. Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. Linear Division The line is defined by a linear division. This option only is available for Inner Contours, Profile Geometries, Section Geometries and Outline Geometries The endpoint is defined by the division in X- and Y- direction. |
|
Fillet radius at the end of a contour segment |
The transition between the single contour elements will be rounded by the inserted value. |
Arc
| Type |
The following options are available for the definition of the arc. Radius and Tangents The arc is defined by a tangent and the position of the endpoint in X- and Y-direction. You can define if the values shall be interpreted absolutely or relatively. Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. You can define with the rotation direction if the shelf runs left or right. Radius and Tangents The arc is defined by the tangents and a radius. The radius always is defined absolutely. You can define with the rotation direction if the shelf runs left or right. Radius and Endpoint The arc is defined by the endpoint and a radius. The radius always is defined absolutely. You can define if the values shall be interpreted absolutely or relatively. Besides you can choose the reference point. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. You can define with the rotation direction if the shelf runs left or right. Two Points Definition of the endpoint and a point on the arc. Beside the two points you can define if the values for the points shall be interpreted absolutely or relatively. Besides you can choose the reference point for both points. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. Radius and Angle The arc is defined by a radius and the angle of start- and endpoint. The radius always is defined absolutely. You can define with the rotation direction if the shelf runs left or right. Endpoint and Center The arc is defined by the endpoint and the center point. Beside the two points you can define if the values for the points shall be interpreted absolutely or relatively. Besides you can choose the reference point for both points. You can choose the last endpoint as well as the four basic points, depend on the sample dimensions. You can define with the rotation direction if the shelf runs left or right. |
|
Fillet radius at the end of a contour segment |
The transition between the single contour elements will be rounded by the inserted value. |