Part Dimensioning
Access
imos Ribbon : Main data > Main data > Element Manager > Output
Organizer > Tab Element Manager > Output
General Information
It is possible to dimension a drawing via the dimensioning principle.
The individual “positions” to be dimensioned are assembled and added to a dimension/dimension chain. No limits are placed on the number of dimensions/dimension chains it is possible to define in a principle. It is possible to define the appearance (dimension type, dimension style) and position (inside, outside, left, right, etc.) of each dimension/dimension chain.
Each row in the grid of a dimensioning principle defines a dimension chain. It is also possible to create groups and use these to influence the appearance of the dimensioning.
Options
Default settings
| Description | Free editable text field |
| Type | It is presently only possible to select the type part dimensioning. |
| Distance between 1st dim. line and object line and object | Defines the spacing between the part and the first dimension line in mm. |
| Distance between dim. lines | Defines the spacing between two dimension lines in mm. |
| Position / origin | Defines the origin to which the dimension should refer. |
Dimensioning
Each row in this grid defines a dimension chain.
| Sequence |
Determines the sequence in which the dimensions/dimension chains are arranged (1 to n). The first line (“1”) is the most inner dimension/dimension chain and the last line (“n”) is the furthest away. Of course, irrespective of this sequence “inside” dimensions are inside of “outside” dimensions! |
| Description | Free editable text field |
| Dimension type | This defines the dimension type (baseline, chain, ordinate dimensioning, etc.) and if the extension lines are to be drawn up to the machining detail to be dimensioned or end at the boundaries of the part (with a small space, which must be set in the AutoCAD Dimension Style Manager). |
| Dimension Style | Assigns an AutoCAD dimension style to the dimension/dimension chain. |
| Grouping |
When defining a dimensioning, there is an option to group the dimensions according to certain criteria.
Corresponding dimension chains are created by "grouping", refer grouping rules. |
| Position |
This is where it is defined where the dimension/dimension chain is to be applied (inside, outside, left, right etc.). A couple of examples for different position settings for a hole with X = 50, Y = 100 in a panel 600x400mm, in which “Quadrant / Origin” is set to “Center center”:
|
| Optimizing Group |
“Optimizing” in this case refers only to leaving out redundant dimensions. For example, if five drillings have the Y-coordinates 100 normally just one dimension should be created and not five. In fact, five are initially created internally - and then four are omitted. You can further influence this with the setting “Optimizing Group”, because two dimensions are never regarded as redundant if they are in different optimizing groups. Incidentally, dimensions with different styles are also never regarded as redundant.
Do not under any circumstances mistake optimizing groups for grouping, they are both completely separate! |
| Dimensioning points | Defines which points are to be included. |
| Filter conditions |
Further restricts the s election of points included via conditions. |
Grouping Rules
Radius, baseline and angle dimensioning contain no chains; consequently, it is always assumed in the following that the dimension style in all principles is set as chain dimensioning or ordinate dimensioning.
- Dimensions from different “dimensioning” rows are never chained in the principle; in other words, there are at least as many dimension chains as there are “dimensioning” rows. Inter alia, due to grouping there can be more dimension chains than rows.
- If one dimension is above and the other below, they are never chained.
- If the value is “standard”, then all dimensions from this dimensioning are chained.
- The values “By radius” / “By X” / “By Y” / “By Z” mean the dimensions will be chained if the corresponding value is matched. This refers to the X / Y / Z of the machining in the part. With “By type, radius, depth and X or Y” the first three values between two dimensions must match for them to be chained. Type is drilling, circular pocket, groove, inner contour etc. For example, a distinction is made between "individual" holes and those in machining groups. If this is not desired, it is possible to alter the code so that these types are viewed as identical or that the behaviour is optional. Moreover, new chains are created for machining procedures with completely different coordinates.
Grouping has two effects:
- For the setting “Continuous dimension” or “Ordinate dimension”: The dimensions belonging to a chain are in a straight line. If there is another chain, which would collide with this one, this is pulled further towards the outside.
- For the setting “Continuous dimension“: The chain is extended up to the edge (or optionally both edges). If, for example, the chain consists of the dimensions 100-200 and 200-350 below the part, another dimension 0-100 or even 350 part width is added. Which of both directions is extended depends on “Quadrant / Origin”.
In contrast, the optimizing group affects neither the number of chains nor the “chains at the edge extension”, but rather only if dimensions are omitted as redundant.